Browse Articles
Discover research articles across all indexed journals
Publisher’s Note: “Vibrational signatures of dynamic excess proton storage between primary amine and carboxylic acid groups” [J. Chem. Phys. 160, 094311 (2024)]
Focusing of airborne ultrasound emitted by a flexurally vibrating plate using a transmission mask with spatially designed holes
We propose a focusing method of intense midair ultrasound out of ultrasonic emission from a single flexurally vibrating plate partially covered with a purposely designed amplitude mask. Many applications relying on nonlinear acoustic effects, such as radiation force employed in acoustic levitation, have been devised. For those applications, focused intense airborne ultrasound is conventionally formed using phased arrays of transducers or sound sources with specific fabricated shapes. However, the former strategies are costly, and the latter may require minute three-dimensional fabrication processes, which both hinder their utilization, especially in constructing a large ultrasound-emitting aperture. Our method offers a possible solution for this, where the amplitude masks are designed depending on the positions of nodes and antinodes of the vibrating plate. We experimentally demonstrate the successful formation of midair ultrasound focus at a desired position, which is localized in a region whose diameter is less than a few wavelengths. Our method only requires a monolithic plate, a driving transducer under the plate, and an amplitude mask fabricated out of laser machining of an acrylic plate. Magnification of the spatial scale of ultrasound apertures based on our method is much more readily and affordably achieved than conventional methods, leading to new midair ultrasound applications with the whole-room workspace.
Effect of temperature on the electrical performance of GaN Schottky barrier impact ionization avalanche transit time diodes
This article investigates the effect of temperature on GaN Schottky barrier Impact Ionization Avalanche Transit Time diodes by Sentaurus TCAD simulations. The findings indicate that Thermal Field Emission increases and the electron saturation velocity decreases with temperature, reducing the avalanche injection phase delay and leading to the transit phase delay exceeding its optimal value. These factors impair the performance of oscillation initiation and conversion output with a shift of bandwidth and optimal frequency towards lower values. Specifically, the start-up efficiency and speed decrease by 69% and 80%, while radio frequency power and efficiency drop by 32% and 41% at the design frequency of 120 GHz under 500 °C. Additionally, the proportion of radio frequency conversion power lost through parasitic resistance increases threefold, and the stability of radio frequency oscillations diminishes by 70%. Therefore, it is recommended to maintain a low junction temperature whenever possible to ensure optimal device performance. In cases where high junction temperatures are unavoidable, reducing the thickness of the drift layer can compensate for the excess transit phase delay, thereby improving performance.
Structural transformation of ZnO quantum dots to ZnO/ZnS core–shell quantum dots and fluorescence color shift from yellow to blue induced by interfacial sulfurization
In recent years, ZnO quantum dots (QDs) synthesized via solution-based methods have garnered significant attention due to their rich surface defects, which lead to strong yellow-green light emissions. However, these defect emissions often limit their optoelectronic performance. Surface engineering of ZnO QDs offers a promising strategy to enhance their properties and enable the construction of core–shell heterostructures. Among various approaches, ion exchange via sulfurization is an effective method to transform ZnO into ZnS, driven by the higher solubility constant of ZnO. In this study, we explore the transformation of ZnO QDs into ZnO/ZnS core–shell QDs through an interfacial sulfurization reaction using thioacetamide. Transmission electron microscopy and x-ray diffraction analyses confirm the successful formation of ZnO/ZnS core–shell QDs. Ultraviolet–Visible (UV–Vis) absorption spectra reveal a significant change: the characteristic Urbach absorption tail of ZnO QDs disappears in ZnO/ZnS core–shell QDs, replaced by a step-like absorption edge at higher energy. Fluorescence spectroscopy further highlights the impact of this structural modification, showing that the intrinsic emission of ZnO is enhanced, while the yellow-green defect emission is quenched. Additionally, a strong blue emission appears around 450 nm, indicative of higher-energy radiative transitions in core–shell QDs. These findings demonstrate that surface sulfurization effectively alters the optical properties of ZnO QDs, facilitating the formation of ZnO/ZnS core–shell QDs with improved emission characteristics. This study underscores the potential of sulfurization as a powerful tool for tuning the optoelectronic properties of semiconductor nanomaterials, with significant implications for their applications in optoelectronics and photocatalysis.
Realization of the square-root Dirac semimetal in electrical circuits
We implement the topological semimetal state generated by the square-root operation in electrical circuits. In this system, the energy bands intersect at finite energies, with the topological properties originating from the parent Hamiltonian. By designing a ribbon circuit, we observe the edge state and measure its frequency spectrum directly, the topological nature of which is characterized by the winding number. Compared to the bidirectional edge state of semimetals that cannot transmit information in a single direction, there is also considerable interest in the unidirectional edge state of Chern insulators. We show that, by introducing the next-nearest-neighbor interactions, the system transforms from a topological semimetal phase to the topological insulator phase, which supports the unidirectional edge modes. Our results show the ability of electrical circuits to realize semimetal states and set examples for other systems to study square-root topological physics.
Color centers and crystal structural transformations induced by femtosecond laser writing in 4H-SiC
Silicon carbide (SiC), a wide-bandgap semiconductor, is gaining importance in quantum technologies due to its promising color centers. Among SiC polytypes, 4H-SiC stands out with its wide bandgap and low impurities, making it ideal for color center research. Femtosecond laser direct writing enables precise creation of color centers, offering nanoscale accuracy. This study explores the optical properties and structural changes in 4H-SiC induced by laser writing. Techniques such as Raman spectroscopy, atomic force microscopy, scanning electron microscopy, and transmission electron microscopy are used to analyze lattice damage and transformations, providing insights into precise color center fabrication and its implications for quantum applications.
A randomized controlled trail comparing the visual stylet and visual laryngoscope for transoral single lumen tracheal intubation
Multilayer stackable grouped acoustic metamaterial with optional sound absorption performance
The control of noise pollution in the low-frequency domain with various spectrum ranges requires the development of a novel tunable sound absorbing material, and a multilayer stackable grouped acoustic metamaterial (MSG-AM) is proposed in this research to obtain the optimal noise reduction effect while minimizing the occupied space. The MSG-AM includes four layers with the eight Helmholtz resonators in each layer divided into three groups, and the total 32 resonators in different layers are connected in parallel. The sound absorption property of each layer is optimized by the joint simulation of finite element simulation and particle swarm optimization algorithm, and the average sound absorption coefficient (SAC) reaches 0.8609 for the first layer in the 535–650 Hz, 0.7126 for the second layer in the 782–937 Hz, 0.9285 for the third layer in the 650–782 Hz, and 0.7615 for the fourth layer in the 435–535 Hz, respectively. The four layers can be combined flexibly to gain the desired sound absorption property in the expected frequency range, and the sequence of multiple layers is a critical factor. The average SAC of the MSG-AM with four layers is improved from 0.3696 for 4 + 1 + 3 + 2 to 0.8726 for 2 + 3 + 1 + 4, and it is better to put behind the layer to obtain absorption in the low-frequency domain and put in front the layer to achieve absorption in the high-frequency domain. The sound absorption mechanism is revealed intuitively through the distributions of thermal power densities, which certify that there exists Helmholtz resonance and Fabry–Pérot resonance effects simultaneously. The proposed MSG-AM is conducive to guarantee the effective control of variable noise.
Identifying risk factors and predicting long COVID in a Spanish cohort
Investigation of surface and interface phonon polariton in nitrogen-implanted GaN epi-layers
In recent decades, gallium nitride (GaN) has garnered significant attention from researchers due to its diverse applications in microelectronics and optoelectronic devices. In this manuscript, using infrared attenuated total reflectance (IR-ATR) spectroscopy, the surface phonon polariton (SPP) and interface phonon polariton modes of unimplanted, N+-ion-implanted, and post-annealed GaN epitaxial layers have been investigated and analyzed at various doses experimentally and theoretically. The position of the SPP mode and its broadening as the increase in implantation doses and post-annealing treatment in the GaN samples are discussed. Shifting in the SPP absorption dip from (698.3–692.7 cm−1) for the unimplanted to implanted dose is correlated with damping factor (ranging from 10 to 80 cm−1) using theoretical reflectance by the model based on damped oscillations between the Ga and N atoms. Unimplanted, implanted, and post-annealed GaN samples Raman spectroscopy and optical absorption have been employed to extract the optical parameters. Optical parameters extracted from Raman spectroscopy and UV–visible spectroscopy such as tensile strain, phonon lifetime, and band-edge absorption have been correlated with the position and broadening of the SPP, as well as the damping factor on unimplanted, N+ ion-implanted, and post-annealed GaN specimens. Notably, the experimental IR-ATR data showed strong agreement with the theoretically modeled results.
Enhancing accuracy in modelling highly multicollinear data using alternative shrinkage parameters for ridge regression methods
Wide-field microwave magnetic field imaging with nitrogen-vacancy centers in diamond
Non-invasive imaging of microwave (MW) magnetic fields with microscale lateral resolution is pivotal for various applications, such as MW technologies and integrated circuit failure analysis. Diamond nitrogen-vacancy (NV) center magnetometry has emerged as an ideal tool, offering micrometer-scale resolution, millimeter-scale field of view, high sensitivity, and non-invasive imaging compatible with diverse samples. However, up until now, it has been predominantly used for imaging of static or low-frequency magnetic fields or, concerning MW field imaging, to directly characterize the same microwave device used to drive the NV spin transitions. In this work, we leverage an NV center ensemble in diamond for wide-field imaging of MW magnetic fields generated by a test device employing a differential measurement protocol. The microscope is equipped with a MW loop to induce Rabi oscillations between NV spin states, and the MW field from the device-under-test is measured through local deviations in the Rabi frequency. This differential protocol yields magnetic field maps of a 2.57 GHz MW field with a sensitivity of ∼9 μT Hz−1/2 for a total measurement duration of T=357 s, covering a 340×340μm2 field of view with a micrometer-scale spatial resolution and a device-under-test input power dynamic range of 30 dB. This work demonstrates a novel NV magnetometry protocol, based on differential Rabi frequency measurement, that extends NV wide-field imaging capabilities to imaging of weak MW magnetic fields that would be difficult to measure directly through standard NV Rabi magnetometry.
PKM2 accelerated the progression of chronic fatigue syndrome via promoting the H4K12la/ NF-κB induced neuroinflammation and mitochondrial damage
Non-destructive measurement of the charge transfer across LaMnO3/SrTiO3 interfaces
Local polarization and charge transfer at the interface between 7-unit cell-thick LaMnO3 (LMO) ultrathin films and substrates composed of Nb-doped (0.05 wt. %) and undoped SrTiO3 (STO) are examined by resonant surface x-ray diffraction. Notably, this photon-in photon-out technique allows us to simultaneously examine the valence distribution and local polarization with minimal radiation damage. Consistent with previous reports, Mn2+ is observed at the interface. Furthermore, the degree of charge transfer is nearly unchanged by the 0.05 wt. % of Nb doping. In the middle of the LMO films, the valence of Mn is 3+. Local polarization estimated from the cation/anion displacements shows that the electric field points outward in the LMO films, and polarization is suppressed in the STO substrate region.
Exploring blood immune cells in the protective effects of gut microbiota on rheumatic heart disease based on Mendelian randomization analysis
Coherent spin transport in a polyacetylene molecular wire
In this study, I theoretically investigated the conduction properties of polyacetylene molecular wires using the Landauer approach based on first-principles approximations. I clarified the influence of π-radicals, which are generated by irregular bond alternation, on the conductivity and transmission spin polarization. It was suggested that, unlike bulk polyacetylene, the presence of π-radicals at the single-molecule level can lead to changes in the conduction properties. Furthermore, I revealed that the behavior of conductivity and transmission spin polarization differs depending on the presence or absence of irregular bond alternation. These findings may provide guidelines for novel device design in the field of molecular electronics.
Comparative analysis of daily global solar radiation prediction using deep learning models inputted with stochastic variables
Abstract Photovoltaic power plant outputs depend on the daily global solar radiation (DGSR). The main issue with DGSR data is its lack of precision. The potential unavailability of DGSR data for several sites can be attributed to the high cost of measuring instruments and the intermittent nature of time series data due to equipment malfunctions. Therefore, DGSR prediction research is crucial nowadays to produce photovoltaic power. Different artificial neural network (ANN) models will give different DGSR predictions with varying levels of accuracy, so it is essential to compare the different ANN model inputs with various sets of meteorological stochastic variables. In this study, radial basis function neural network (RBFNN), long short-term memory neural network (LSTMNN), modular neural network (MNN), and transformer model (TM) are developed to investigate the performances of these algorithms for the DGSR prediction using different combinations of meteorological stochastic variables. These models employ five stochastic variables: wind speed, relative humidity, minimum, maximum, and average temperatures. The mean absolute relative error for the transformer model with input variables as average, maximum, and minimum temperatures is 1.98. ANN models outperform traditional models in predictive accuracy.
Electrical activities of sulfur dopants in GaAs introduced by self-assembled molecular monolayers
Self-assembled molecular monolayer doping remains as a research focus for its nature of being conformal, nondestructive, and self-limiting. However, the carrying molecules may contaminate the substrate and electrically deactivate the dopants. In this work, we investigate the electrical activities of sulfur dopants in GaAs introduced by the self-assembled molecular monolayer doping technique. The results from secondary ion mass spectrometry and low-temperature Hall measurements show that the activation energy of sulfur dopants is 68 meV, and that 91% of these dopants introduced into GaAs by the self-assembled molecular monolayer doping technique are electrically active. The impact of the carrying molecular contamination is minimal. We employ this monolayer doping technique to create a PN junction diode on a p-type GaAs substrate. The PN junction diode exhibits an outstanding performance with an ideality factor of 1.26 and a rectification ratio up to 104 within the bias of ±0.6 V.
Random mechanisms govern bacterial succession in bioinoculated beet plants
Abstract Plant colonization by microbes is an example of succession, with its distinct phases differing in community structure and diversity. This process needs to be studied to improve bioinoculation strategies. Here, we show that, regardless of bioinoculation, soil type and plant genotype, bacteria colonize the rhizosphere and tissues of axenic beets in two phases associated with taproot development. Communities remained stable after five weeks of growth in soil. Time, soil type and genotype determined community structure both in the rhizosphere and in the endosphere. Inoculation changed the community structure, and members of Pseudomonadota and Bacillota were recruited by beets. Axenic beet colonization runs through phases similar to colonization of a glacier forefront, and bacteria are recruited mostly randomly. The transition from the early to late phase involves a decrease in the bacterial load in plant tissues, which may be linked to plant growth and the arrest of bacterial cell division. Therefore, early inoculation seems to be favourable. Five weeks of growth in soil enabled formation of stable bacterial communities in both the rhizosphere and the endosphere. The influence of inoculation seems to be indirect, probably due to microbe-microbe interactions.
Power dependence of electron paramagnetic resonance: Analytical solution of Landau–Lifshitz–Gilbert equation
The solutions of the Landau–Lifshitz–Gilbert (LLG) equation reveal nonlinear effects in electron spin dynamics. Here, the nonmonotonic power dependence of the electron paramagnetic resonance (EPR) signal intensity is derived by solving the LLG equation. The analytical solutions of a spin moment are obtained for linearly polarized microwaves with any power. A tendency of susceptibility from linear to nonlinear is exhibited with increasing microwave power. Both low- and high-power dependences of EPR signal intensity of standard sample 1,3-bisdiphenylene-2-phenylallyl are well explained by the tendency. These findings provide valuable insights into nonlinear behavior of spin dynamics and the quantitative analysis of paramagnetic centers.